acid maria

Fabled Hits Supergene Quartz Breccia Over 1.35 Meters Grading 689.56 g/t Ag Eq

 

Fabled Silver Gold Corp. ("Fabled" or the "Company") (TSXV:FCO)(OTCQB:FBSGF)(FSE:7NQ) is pleased to announce additional results from underground diamond drilling of the 1,200 meter underground drill program at the "Santa Maria" Property in Parral, Mexico, see Figure 1

 

Figure 1 - Longitudinal View of Area of Current Underground Drilling

 

Drill hole SMUG21- 14 was drilled approximately 50 meters east of drill hole SMUG21- 13, which reported 541.49 g/t Ag Eq, while drill hole SMUG21- 15 was drilled approximately 50 meters west of hole 13. Each hole was designed to hit the hole 13 mineralization at the same vertical elevation underground of -125 meters.

 

Drill Hole SMUG21-14

 

SMUG21-14 was drilled at a dip of -45 degrees and was successful in the interception of the Santa Maria footwall wall structure, a low-grade hydrothermal breccia, and a mineralized diorite dike with quartz veining at the hanging wall structure.

 

The collar, or the beginning, of hole SMUG21-14 reported 7.20 meters grading 93.19 g/t Ag Eq, including 2.15 meters located in the footwall of the Santa Maria structure and reporting 168.21 g/t Ag Eq.

 

Adjacent to the hanging wall zone, a mineralized diorite was encountered with a supergene enriched quartz vein breccia on the lower contact. The diorite dike interval of 6.7 meters assayed 193.98 g/t Ag Eq, including the contact with the lower vein breccia, which graded 313.26 g/t Ag Eq over 3.85 meters, and the supergene quartz breccia reporting 1.35 meters of 689.56 g/t Ag Eq. See Figure 2 below and Photos 1 of foot wall mineralization and photo 2 of the hanging wall mineralization.

 

Figure 2- Cross Section of Underground Drill Hole SMUG21- 14

 

Table 1- Drill hole SMUG 21- 14 Assay Results

 
                                                            

Drill Hole

From m

 

To

 

m

 

Width m

Au g/t

Ag g/t

AgEq* g/t

Pb %

Zn %

Cu %

SMUG21-14

0.00

7.20

7.20

0.23

81.36

93.19

0.07

0.13

0.01

Including

4.00

6.15

2.15

0.49

143.00

168.21

0.15

0.27

0.01

 

99.15

105.90

6.75

0.33

177.00

193.98

0.10

0.36

0.01

Including

99.15

103.00

3.85

0.53

286.00

313.26

0.16

0.57

0.01

Including

99.15

100.50

1.35

1.08

634.00

689.56

0.29

0.88

0.02

 
  • ** Ag Equivalent ("Ag Eq") grade is calculated using $20 per ounce Ag and $1,600 Au

Photo 1- Drill hole SMUG 21- 14 Foot Wall Oxidized Vein and Diorite Dike

 

Photo 2- Drill hole SMUG 21- 14 Hanging Wall, Highly Fractured, Oxide Mineralized Diorite Dike

 

Supergene Enrichment Over 1.35 Meters on The Lower Contact

 

Drill Hole SMUG21-15

 

Underground drill hole SMUG21- 15 was drilled in the same plane as SMUG21- 14 but collared 50 meters to the west of hole SMUG21-13.

 

SMUG21-15 was drilled at -45 degrees and was again successful in intercepting the mineralized foot wall structure, followed by a hydrothermal breccia and the hanging wall Santa Maria structure the at a vertical depth of -125 meters.

 

From the beginning, or the collar, of hole SMUG21-15, and as in the case of holes SMUG21- 13 and 14, the footwall of the Santa Maria structure was intercepted over a distance of 7.90 meters grading 67.50 g/t Ag Eq, which includes 2 intercepts of 1.50 meters which graded 134.11 and 135.58 g/t Ag Eq.

 

A 1.20 meters intercept of hydrothermal breccia assayed 67.35 g/t Ag Eq which was followed by the hanging wall zone of 1.80 meters, of which 0.20 meters reported 495.50 g/t Ag Eq at the bottom contact of the structure. See Figure 3 below and photos 3 of the Santa Maria foot wall zone and photo 4 of the lower contact of the hanging wall.

 

Figure 3- Cross Section of Underground Drill Hole SMUG21- 15

 

Table 2- Drill hole SMUG21-15 Assay Results

 
                                                                                

Drill Hole

From m

 

To

 

m

 

Width m

 

Au

 

g/t

 
 

Ag

 

g/t

 

AgEq* g/t

 

Pb

 

%

 
 

Zn

 

%

 
 

Cu

 

%

 

SMUG21- 15

0.00

7.90

7.90

0.09

62.87

67.50

0.09

0.14

0.01

Including

0.00

1.50

1.50

0.04

132.00

134.11

0.04

0.05

0.00

Including

1.50

3.00

1.50

0.08

90.30

94.16

0.04

0.06

0.00

Including

6.60

7.00

0.40

0.44

113.00

135.58

0.15

0.15

0.01

 

79.80

81.00

1.20

0.11

61.90

67.35

0.00

0.03

0.00

 

87.75

89.60

1.80

0.09

63.86

68.49

0.04

0.09

0.00

Including

89.40

89.60

0.20

0.38

495.50

495.50

0.26

0.72

0.01

 
  • ** Ag Equivalent ("Ag Eq") grade is calculated using $20 per ounce Ag63.86 and $1,600 Au

Photo 3,4 - SMUG21-15 Oxidized Diorite Dike at Santa Maria Footwall

 

Photo 5 - SMUG21-15; Santa Maria Hanging Wall Vein.

 

FUTURE UNDERGROUND DRILLING UPDATE

 

Holes SMUG21- 16, 17 and 18 have been completed and submitted for assay. Hole SMUG21- 18 is the last hole drilled for the underground drill campaign.

 

QA QC Procedure

 

Analytical results of sampling reported by Fabled Silver Gold represent core samples that have been sawn in half with half of the core sampled and submitted by Fabled Silver Gold staff directly to ALS Chemex, Chihuahua, Chihuahua, Mexico. Samples were crushed, split, and pulverized as per ALS Chemex method PREP-31, then analyzed for ME-ICP61 33 element package by four acid digestions with ICP-AES Finish. ME-GRA21 method for Au and Ag by fire assay and gravimetric finish, 30g nominal sample weight.

 

Over Limit Methods

 

For samples triggering precious metal over-limit thresholds of 10 g/t Au or 100 g/t Ag, the following is being used:

 

Au-GRA21 Au by fire assay and gravimetric finish with 30 g sample.

 

Ag-GRA21 Ag by fire assay and gravimetric finish.

 

Fabled Silver Gold monitors QA/QC using commercially sourced standards and locally sourced blank materials inserted within the sample sequence at regular intervals.

 

About Fabled Silver Gold Corp.

 

Fabled is focused on acquiring, exploring and operating properties that yield near-term metal production. The Company has an experienced management team with multiple years of involvement in mining and exploration in Mexico. The Company's mandate is to focus on acquiring precious metal properties in Mexico with blue-sky exploration potential.

 

The Company has entered into an agreement with Golden Minerals Company (NYSE American and TSX: AUMN) to acquire the Santa Maria Property, a high-grade silver-gold property situated in the center of the Mexican epithermal silver-gold belt. The belt has been recognized as a significant metallogenic province, which has reportedly produced more silver than any other equivalent area in the world.

 

Mr. Peter J. Hawley, President and C.E.O.

 

Fabled Silver Gold Corp.
Phone: (819) 316-0919
peter@fabledfco.com

 

For further information please contact:
info@fabledfco.com

 

The technical information contained in this news release has been approved by Peter J. Hawley, P.Geo. President and C.E.O. of Fabled, who is a Qualified Person as defined in National Instrument 43-101 - Standards of Disclosure for Mineral Projects.

 

Neither the TSX Venture Exchange nor its Regulations Service Provider (as that term is defined in the policies of the TSX Venture Exchange) does accept responsibility for the adequacy or accuracy of this news release.

 

Certain statements contained in this news release constitute "forward-looking information" as such term is used in applicable Canadian securities laws. Forward-looking information is based on plans, expectations and estimates of management at the date the information is provided and is subject to certain factors and assumptions, including, that the Company's financial condition and development plans do not change as a result of unforeseen events and that the Company obtains any required regulatory approvals.

 

Forward-looking information is subject to a variety of risks and uncertainties and other factors that could cause plans, estimates and actual results to vary materially from those projected in such forward-looking information. Some of the risks and other factors that could cause results to differ materially from those expressed in the forward-looking statements include, but are not limited to: impacts from the coronavirus or other epidemics, general economic conditions in Canada, the United States and globally; industry conditions, including fluctuations in commodity prices; governmental regulation of the mining industry, including environmental regulation; geological, technical and drilling problems; unanticipated operating events; competition for and/or inability to retain drilling rigs and other services; the availability of capital on acceptable terms; the need to obtain required approvals from regulatory authorities; stock market volatility; volatility in market prices for commodities; liabilities inherent in mining operations; changes in tax laws and incentive programs relating to the mining industry; as well as the other risks and uncertainties applicable to

 

the Company as set forth in the Company's continuous disclosure filings filed under the Company's profile at www.sedar.com. The Company undertakes no obligation to update these forward-looking statements, other than as required by applicable law.

 

SOURCE: Fabled Silver Gold Corp.

 

View source version on accesswire.com:
https://www.accesswire.com/662870/Fabled-Hits-Supergene-Quartz-Breccia-Over-135-Meters-Grading-68956-gt-Ag-Eq

News Provided by ACCESSWIRE via QuoteMedia

The Conversation (0)
Gold bars with text: "5 Top Canadian Mining Stocks This Week."

Top 5 Canadian Mining Stocks This Week: Avanti Gold Gains 158 Percent on Misisi Settlement

Welcome to the Investing News Network's weekly look at the best-performing Canadian mining stocks on the TSX, TSXV and CSE, starting with a round-up of Canadian and US news impacting the resource sector.

Statistics Canada released its June Labour Force Survey on Friday (July 11). The data indicated that 83,000 new jobs were added to the workforce, led by 34,000 new employees in the wholesale and retail trade category and a 17,000 worker rise in the healthcare and social assistance category.

In other positive news for the Canadian job market, the overall employment rate rose by 0.1 percent to 60.9 percent, while the unemployment rate declined by 0.1 percent to 6.9 percent.

Keep reading...Show less
Gold bar on nuggets with "5 Top Australian Mining Stocks" text overlay.

Top 5 Australian Mining Stocks This Week: Yandal Shares Double on Arrakis Drilling Results

Welcome to the Investing News Network's weekly round-up of Australia’s top-performing mining stocks on the ASX, starting with news in Australia's resource sector.

This week's top-performing stocks list is dominated by oil and gas companies, alongside gold and lithium companies.

In Australian mining news, the Fair Work Commission ruled that BHP (ASX:BHP,NYSE:BHP,LSE:BHP) must raise the wages of 2,200 workers at three coal mines in Queensland. The workers in question were employed indirectly through a hiring firm and were being paid significantly less than their peers working directly under BHP.

The case was brought by two worker's unions and based on the Same Job, Same Pay reforms made by the government last year. To align wages, the FWC ruled BHP must raise the labour hire employees' wages by AU$30,000 each.

Keep reading...Show less
Pilbara region, Western Australia, Australia.

Pilbara 2.0: Inside Australia’s Newest Gold Frontier

The Central Pilbara region of Western Australia is undergoing a quiet revolution that is rapidly reshaping the global gold exploration landscape.

Once dismissed as a technically challenging and geologically inconsistent terrain, Pilbara is now emerging as one of the world’s most exciting new gold frontiers and drawing serious attention from institutional investors, driven by transformative discoveries, a maturing geological model and a wave of junior explorers tapping into underexplored intrusive-hosted systems.

Anchored by the multimillion-ounce Hemi discovery — one of the most significant gold finds in Australia in over a decade — this region is not just proving its geological potential, but also demonstrating the kind of scale, consistency and margin profile that modern gold investors seek. As the discovery window remains wide open and valuations are still accessible, the Central Pilbara presents a rare opportunity for early exposure to what may become one of Australia’s next tier-one gold districts.

Keep reading...Show less
A mining truck within the outline of Australia's map on a clear day.

Is Australia on the Brink of a New Mining Super Cycle?

Mining remains as a cornerstone of Australia’s GDP and export earnings, but current global challenges such as trade disputes and price changes may be straining its foundations.

A recent FocusEconomics report tackled Australia’s resource wealth, tracing from the gold rushes of the 1850s to the iron ore and coal booms of the 21st century.

Keep reading...Show less
Kobo Resources Confirms Additional High-Grade Gold Mineralization at Kossou with 15.5 m at 2.3 g/t Au, incl. 8.3 m at 3.43 g/t Au; Outlines Next Phase of Exploration at Kossou

Kobo Resources Confirms Additional High-Grade Gold Mineralization at Kossou with 15.5 m at 2.3 g/t Au, incl. 8.3 m at 3.43 g/t Au; Outlines Next Phase of Exploration at Kossou

 
  •   High-grade gold intercepts highlighted by 15.5 m at 2.30 g/t Au, incl. 8.3 m at 3.43 g/t Au at the Road Cut Zone  
  •  
  •   Initial drilling on the gap between Jagger and Road Cut Zone confirms target structure, warrants further testing  
  •  
  •   Current drill phase complete; Geological modelling and planning underway for 15,000 m drill program expected to begin in H2 2025  
  •  

 

 Kobo Resources Inc. (" Kobo" or the " Company ") ( TSX.V: KRI ) is pleased to report additional diamond drill results from the Road Cut Zone at its 100%-owned Kossou Gold Project (" Kossou ") in Côte d'Ivoire. Results from these holes continue to strengthen the Company's understanding of the key structural controls that define this prospective target area.

News Provided by Business Wire via QuoteMedia

Keep reading...Show less

Latest Press Releases

Related News

×